Sealed bearing extractor for 29mm ID bearings. Extractor has 1/2" thru hole for use with our 1/2" threaded rod press handles. - This extractor is part of a system that requires additional pieces to function.
This 29mm open bore adapter is used to press 29mm x 42mm (DUB) sealed bearings. The adapter is machined with one step at 29mm OD, which fits into the center of the sealed bearing. For use with Wheels Mfg. bottom bracket press (PRESS-7 , PRESS-7-PRO or PRESS-9-PRO). - Inner step outer diameter: 28.9mm - Outer diameter: 41.8mm - Thru hole diameter: 12.8mm (1/2-inch) - Thickness: 7mm - Machined, red anodized aluminum - Sold individually
BB30 service kit for SRAM DUB cranks. - Includes (2) Enduro 6806/29 ABEC-3 sealed bearings and 2 retaining clips - Bearing Dimensions: OD: 42mm / ID: 29mm / Width: 7mm - Enduro ABEC-3 bearings - Use with SRAM DUB cranks Note: SRAM DUB cranksets are not designed to work in 68mm or 73mm wide shells with inboard bearings. Use only if your frame is a direct-fit bearing system, and the BB shell width is 86.5mm or wider.
- Anodized aluminum construction. Includes mounting hardware - Measures threads for all cones, locknuts and axles - Metric measurement on one side and Standard on the other side
Use this double-sided socket tool for installing and removing both 48.5mm and 44mm 16-notch bottom bracket cups. Socket is machined for 1/2-inch drive, but a 3/8-inch to 1/2-inch adapter is included so you can use it with 3/8-inch drive torque wrenches. - Compatible with all Wheels Manufacturing bottom brackets that have 48.5mm or 44mm, 16-notch spline patterns - Also compatible with FSA MegaEVO BB cups, Shimano, SRAM/Truvativ, Campagnolo Ultra Torque, and FSA - Machined 6061 aluminum - Anodized red
This Wheels Mfg. Double End Bottom Bracket wrench fits 16-notch bearing cups with an outside diameter of 44mm as well as 16-notch bearing cups with an outside diameter of 48.5mm. - Machined aluminum - Anodized red. - Compatible with all current Wheels Mfg bottom brackets with notched cups
Wheels Manufacturing open bore adapters are used to press sealed cartridge bearings into place. The adapters are machined with one step to correspond to the bearing OD, which fits in to the center of the sealed bearing and an outside diameter to accommodate the bearing's outer diameter. Size: [Bearing inner diameter] x [Bearing outer diameter] Note: If only one dimension is given, that is the outer diameter of the adapter, with no inner diameter step
Wheels Manufacturing Over Axle Adapters are used for pressing your most commonly used bearing sizes into place. Each represents an excellent addition to the Press-4 Bearing Press. - Adapters sold individually
Replacement handle assembly for Wheels Mfg. large sealed bearing press (PRESS-1). Primarily designed for pressing bearings into hubs. Note: rod diameter is smaller than the hole size in Wheels Mfg. universal bottom bracket drift. Includes: - Machined fixed end aluminum "T" handle with brass insert - Machined non-fixed end aluminum "T" handle with brass insert - 3/8" x 12TPI threaded rod - M5x12mm flat head screw to secure fixed-end handle to rod
Wheels Manufacturing Sealed Bearing Extractor - 10mm Fits the following bearings: - 6000 - 6200 - 6800 - 6900
Wheels Manufacturing Sealed Bearing Extractor - 15mm Fits the following bearings: - 6002 - 6702 - 6802 - 6902 - 15267 - 15268
Wheels Manufacturing Sealed Bearing Extractor - 10mm Fits the following bearings: - 6704 - 6804 - 6904
Wheels Manufacturing Sealed Bearing Extractor - 30mm Fits: - 6806 - Other bearings with an inside diameter of 30mm
The Wheels Manufacturing universal bottom bracket drift presses all current Wheels Mfg bottom bracket cups into your frame or bearing cups. The adapter is machined with multiple steps to fit common bottom bracket shell and bearing diameters listed below. Each step is laser etched with the diameter size. - Inner hole sized to fit 1/2" threaded rod. Not for use with Wheels Mfg PRESS-1 or PRESS-4 - Compatible with any other press with a 1/2" diameter rod - Recommended for use with Wheels Mfg Universal BB Press - Machined aluminum - Anodized Red - Sold individually - Drift can also be used as a frame bottom bracket shell sizing guide! Fits the following bottom bracket shell sizes: - BB30 (42mm) - PF30 (46mm) - BB86, BB92 (41mm) - BBRight (46mm) - BB386EVO (46mm) - Cannondale BB30A (42mm) - Cannondale PF30A (46mm) - Specialized Carbon OSBB (46mm) - Specialized Alloy OSBB (42mm) - TREK BB90, BB95 (37mm) - PF24 (41mm)
This do-it-all universal bottom bracket press is designed to press in all current Wheels Mfg. bottom brackets. Economical and easy to use, this tool is made up of two machined aluminum handles, a 1/2-inch threaded rod, and two machined aluminum drifts. Each drift is machined with multiple steps to fit common bottom bracket shell and bearing diameters. No more searching for the correct size drifts and parts—just match up the drift to your frame's BB shell size and your bottom bracket's bearing size, and press away. - Zinc-plated 1/2-inch diameter threaded rod resists bending, allowing for the cups to align and press in straight - Drifts can also can be used as a frame bottom bracket shell sizing guide - Machined aluminum handles and drifts - Red anodized drifts and handles - Steps on drift are marked with diameter sizes - Works with BB shells up to 132mm wide - Includes two universal BB drifts
Page 1 of 1